Chimney Company in Chino — One Flat Price, You See What We See

Chimney Company in Chino, CA

Chimney repair in Chino usually means one of two jobs: restoring a 1960s masonry chimney in the 91710 ranch tracts that has cracked tiles and spalled mortar, or bringing a newer factory-built vent system in the 91708 corridor back to spec. Ontario Chimney has served Chino since 2014, and the work here follows the housing stock. We handle sweeps, repairs, caps, crowns, liners, and dryer vents with the same trained technicians from first inspection through final repair, so you’re not chasing a cleaner who hands you off to a contractor. Call (833) 467-7685 for a free estimate.

Call (833) 467-7685

Why Chino Homes Are Different

Chino’s fireplace stock splits sharply along its ZIP codes. The 91710 core is mostly mid-century single-story ranch and tract housing built from the 1950s through the 1980s. Those homes have traditional masonry fireplaces with clay flue tiles, and many haven’t been properly inspected in years. In the older west-side tracts, we regularly find original clay tiles with hairline cracks that past sweeps never flagged because a brush passes right over them. The bigger issue is firebox mortar: decades of heat cycling in dry inland air causes spalling, where the mortar face crumbles off in chunks. That’s a structural red flag, not a cosmetic one.

The 91708 growth corridor on the east side is a different animal. Apartment and townhome complexes built after 2000 use factory-built fireboxes and direct-vent gas inserts. These units need manufacturer-specific service intervals and venting checks that a generic sweep doesn’t cover. Then there’s the climate. Inland Empire Santa Ana winds hit Chino hard in fall, and cold winter nights push fireplaces into real duty from December through February. But the long, hot dry season from May through October leaves chimneys idle for months at a stretch. Creosote hardens during that idle time, which actually makes it harder to remove than the soft, flaky buildup you get from regular use. Wildfire smoke from the dry brush inland adds another layer of particulate that cakes onto flue walls. Ember containment here isn’t a nicety. It’s a fire-safety calculation.

Our Main Chino Services

Most Chino calls start with one of two things: a fireplace that hasn’t been touched since the previous owner moved out, or a dryer that takes two cycles to dry a load and vents into a wall cavity with years of trapped lint. Here’s how we handle both in Chino.

Chimney Sweep in Chino

A proper sweep in Chino starts with the flue, not the firebox floor. In the 91710 ranch homes, that means checking clay tile joints for cracks and running a camera when the brush reveals anything suspicious. In the 91708 gas-unit stock, the sweep is about clearing heat-exchanger dust and confirming the direct-vent termination is clear of debris and ember exposure. One thing to know: a sweep that ignores the tile joints is the norm around Chino, not the exception. Our technicians don’t do walkthrough sweeps. We document what we find, show you the evidence, and tell you plainly if a repair can wait or if it should be scheduled before burning season. See the full breakdown on our Chimney Sweep in Chino page.

Dryer Vent Cleaning in Chino

Dryer vents are a leading cause of house fires, and the NFPA’s data backs that up. In Chino’s older 91710 homes, dryer vents often run long horizontal distances through slab foundations or out the roof, which means lint accumulates faster and is harder to reach. In the newer 91708 townhomes, vents share walls with neighbors and build codes require more frequent cleaning intervals. We treat this as a standalone fire-safety service, not a tag-along to a sweep. The cleaning includes a full duct run inspection, lint removal, and a photo report so you can see the before and after. Details are on our Dryer Vent Cleaning in Chino page.

Chimney Repair in Chino

Chimney repair in Chino usually traces back to the 1950s-70s masonry stock in 91710. Cracked clay flue tiles and spalled firebox mortar are common finds, and they can’t be fixed with a sweep. In the 91708 corridor, we also see factory-built units where the termination cap has rusted through or the venting joints have separated. Either way, the repair starts with a camera inspection so we can show you exactly what’s failing and what it will take to fix it. Our Chimney Repair service covers the full scope, from small component swaps to full flue restoration and liner installs, all under the same crew.

Chimney Cap Installation

Signs you need it

You see rust flakes or nesting material inside the firebox, or you’ve had birds, squirrels, or rain coming down the flue during spring showers.

What it costs in Chino

Chimney cap installation in Chino typically runs $250 to $650 depending on flue size, material, and whether the crown needs any prep work first.

How we do it

We measure the flue opening, select a stainless or copper cap sized to the tile, set it with mechanical fasteners, and confirm the spark arrestor mesh meets ember-containment standards for Chino’s wildfire-prone dry season.

Chimney Crown Repair

Signs you need it

The concrete crown at the top of your chimney has visible cracks, gaps, or spalled sections where water can seep into the masonry and freeze-thaw during Chino’s cold winter nights.

What it costs in Chino

Crown repair in Chino typically falls between $400 and $900 depending on the size of the damaged area and whether we’re patching or fully resurfacing.

How we do it

We remove loose material, rebuild the crown with a proper Portland-based mix, add a slight slope for water runoff, and seal the crown-to-flue-tile joint so rain can’t work its way back in.

Chimney Flashing Repair

Signs you need it

You have water staining on the ceiling near the chimney chase, or the metal flashing where the chimney meets the roofline has lifted, rusted, or pulled away from the masonry.

What it costs in Chino

Flashing repair in Chino typically runs $450 to $1,200 depending on whether we’re resealing existing flashing or cutting in new step flashing under shingles.

How we do it

We remove the old flashing, install new step and counter-flashing with proper overlap, and seal all transitions with a high-temperature roofing mastic that holds up to Santa Ana wind-driven rain.

Chimney Liner Installation

Signs you need it

A camera inspection shows cracked or missing clay tile sections, or you have a gas appliance venting into an unlined flue that isn’t code-compliant for Chino’s combination of cold starts and ember exposure.

What it costs in Chino

Liner installation in Chino typically ranges from $1,900 to $4,100 depending on flue length, offset angles, and whether we’re installing a DuraFlex stainless system or resurfacing with HeatShield ceramic.

How we do it

We run a camera to confirm flue dimensions, pull a DuraFlex stainless liner or apply HeatShield ceramic resurfacing depending on the flue condition, and re-verify the system with a final camera pass.

What Chimney Repair Costs in Chino

Do I really need a new liner if the old clay tiles are still there?

Not always. Cracks in clay tiles are the trigger, but HeatShield ceramic resurfacing can often restore the flue without a full liner tear-out. We show you the camera footage so you can decide with the evidence in front of you. Call (833) 467-7685 for an inspection.

Can chimney repairs wait until after burning season?

Some can, but cracked flue tiles and separated venting joints should not wait if you plan to use the fireplace. Creosote ignites at around 451 degrees inside a damaged flue, and Chino’s hard, dry buildup is exactly the kind that catches. Get it looked at before December.

Brands We Service in Chino

We work with professional-grade materials, not hardware-store substitutes. That means DuraFlex stainless liner systems for relining jobs, HeatShield ceramic for flue resurfacing, and components from Famco, Copperfield, and Olympia Chimney for caps and dampers. Parts are stocked locally for most Chino jobs, so repairs don’t stall waiting on a distributor. See our brands for the full lineup.

Pricing for Chimney Company in Chino, CA

Neighborhoods We Serve in Chino

Our service area covers both Chino ZIP codes: 91710 on the older west side with its ranch and tract housing, and 91708 on the newer east side with its townhome and apartment builds. We work across the full city, from the original downtown grid out to the growth corridor near the 71.

• Downtown Chino (91710)
• College Park (91710)
• The Preserve (91708)
• Chino Meadows (91710)
• Kimball neighborhood (91710)

Most Chino appointments are scheduled within a few business days, with a tighter window once December approaches and the burning season is in full swing.

Service Area – Cities Near Chino

Our trucks run daily from Ontario, which means Chino sits inside our normal coverage radius without a trip charge. We also serve the neighboring communities of Los Serranos, CA, Ontario, CA, Montclair, CA, and Eastvale, CA. If your chimney or dryer vent is anywhere in the Chino Valley, we can get to it.

FAQs About Chimney Company in Chino